BZCY600BZY hydraulic well drilling rig is direct rotary drilling rig. The truck chassis uses SINOTRUK brand 8×4 special chassis, 11.00R20 steel off-road tire tread, with good off-road performance.
Inner diameter of the rotary table(mm)
Speed of turntable(r/min)
Torque of turntable(KN.m)
Single rope lifting capacity of main windlass(KN)
The capacity of main windlass(KN)
Single rope lifting capacity of tool windlass(KN)
The rope capacity of tool windlass(m)
The lifting capacity of hook(KN)
Bearing capacity of mast (KN)
The effective height of mast (mm)
The height of mast (mm)
Bearing capacity (t)
Assistant pipe (mm)
Pump delivery (ml/r)
Rated speed (r/min)
Diameter of cylinder (mm)
100 110 120 130 140
Stroke of piston (mm)
Theory of flow (L / min)
Rated pressure (Mpa)
Pounding times (min-1)
Diameter of suction tube (mm)
Diameter of drain pipe (mm)
Input speed (r / min)
Input power (kw)
Overall dimensions (mm)
SINOTRUK D10.27-40diesel engine
Drilling rig engine
CUMMINS 6BTA5.9-C180 diesel engine
Rated power (kw)
The best working gear (or speed)
The highest speed(Km/h)
1. Can it work with tricone bit?
Yes, it can. We can equip tricone bit as your size, and together with connector for drill bit and drill rod, for your convenient use.
2. Can it drill hard rocks? How fast?
First, the ground type can be soil, sand, gravel, hard rocks, mixed ground, etc. Second, if your ground is all large blocks of granite, limestone, we will suggest you use our other models, like BZC-series, which is air compressor feeding type, specially designed for complete blocks of hard rocks.
The drilling speed in soil and sand is 15~25m per hour.
The drilling speed in rocks is 6~8m
The drilling speed in hard rocks, like granite, is 1~2m per hour.
3. Can it be customized as crawler type?
Yes, sure. as following picture:
The legs are hydraulic type.
4. what kinds of drill bits can we use for BZC600BLBC water well drilling machine?
Three wing bit for open hole, or drill in soil, sand, and gravel.
Alloy bit is for soil, sand and very soft rock ground.
PDC bit is to drill soft rock and hard rock.
1. All the members should listen to the unified command of the captain, The workers should wear a helmet, and with the safety belts when climb the tower.
2. It is a good job to record the drilling process.
3. In the process of drilling, it is necessary to pay attention to the changing situation at any time, if there is unusual noise, turn resistance increases, mutation load, the pressure of mud is inadequate , the mud reduce or not to return back, etc. It is necessary to immediately take measures to deal with the abnormality. If it is of no effect, please lift the tools and check.
4. In the loose stratum, it should not be a long time to drill, and it must be slowly to lift or fall the tools. When drill or complete, it must inject the mud to the hole at once, it will prevent the collapse.
5. If the tools are locked in the hole, it must act the tools up an down. When the tools are loosed, and then lift the tools.
6. When complete the drilling, it must lift out the tools and put them to the safe place, it will prevent burying the tools.
7.Adjusted according to different strata of the viscosity of drilling mud, and select the appropriate bit or other drilling method used.
8. It is strictly prohibited to make the rig be in the long-term overloading situation.
9. Can not bump the screw thread of drill pipe when carry them, take protective measures. When use the dill pipe, please clean the screw thread and smear grease.
10. The compression device using the wire rope is used only mild pressure in the hard layer.(And the pressure is less than 1 ton) It must not be forced, otherwise the bored will easily tilt. So it is recommended to use drill collar to press.